기술
읽는 시간 11분

AirPods Noise Cancellation Not Working? 7 Proven Fixes

Side view of a young woman wearing white wireless earbuds against a light background

Active Noise Cancellation on AirPods Pro or AirPods Max that stops working, sounds weaker than it used to, or lets outside noise through as if it were turned off is almost always caused by dirty external microphones, a poor ear tip seal, or a firmware glitch. When airpods noise cancellation not working becomes an issue, the cause is usually something you can fix yourself. ANC relies on external microphones to pick up ambient sound, an internal processor to generate an inverted sound wave, and a tight seal in your ear canal to block passive noise. If any one of these three components is compromised, noise cancellation performance drops dramatically or fails entirely.

Person wearing wireless earbuds while relaxing on a couch with eyes closed

Photo by cottonbro studio on Pexels

Why AirPods Noise Cancellation Stops Working — Airpods Noise Cancellation Not Working

The wrong noise control mode is selected. AirPods Pro and AirPods Max have three noise control modes: Active Noise Cancellation, Transparency, and Off. If the mode was accidentally switched to Transparency or Off, outside noise passes through normally. This happens more often than expected because the mode can be changed by squeezing the AirPod stem, pressing the noise control button on AirPods Max, or through Control Center, and an accidental touch can switch modes without you realizing it.

The external microphones are blocked by dirt or debris. ANC works by using outward-facing microphones on each AirPod to capture ambient sound. The ANC processor then generates an anti-phase sound wave that cancels the noise before it reaches your ear. If the external microphones are clogged with earwax, pocket lint, sweat residue, or dust, they cannot accurately capture ambient sound. The anti-noise signal becomes inaccurate, and cancellation either weakens significantly or produces strange artifacts like a low hum or intermittent crackling.

The ear tips do not create a proper seal. ANC performance depends heavily on passive noise isolation from the ear tips. If the silicone tips are the wrong size for your ear canals, worn out from extended use, or not seated correctly on the AirPod, outside noise leaks in around the seal. The ANC system cannot compensate for a large physical gap because it is designed to cancel noise that passes through the sealed ear tip, not noise that bypasses it entirely. A poor seal is the second most common cause of weak ANC after dirty microphones.

A firmware bug is disabling or degrading ANC. Apple has released firmware updates in the past that inadvertently weakened ANC performance on AirPods Pro. Community reports after certain updates described noticeably reduced noise cancellation compared to the previous firmware version. While Apple typically addresses these regressions in subsequent updates, a firmware glitch can make ANC feel broken even when the hardware is functioning correctly.

Only one AirPod is being used. On AirPods Pro 1st generation, ANC is not available in single-AirPod mode. AirPods Pro 2nd generation supports ANC with a single AirPod, but performance is reduced. Make sure both AirPods are in your ears for full noise cancellation.

An accessibility setting is overriding the noise control mode. The Accessibility settings for AirPods allow customizing what the press-and-hold gesture does. If this gesture has been reassigned away from noise control cycling, you may not be able to switch to ANC using the stem squeeze.

Verify That ANC Is Active

Before troubleshooting hardware or settings, confirm that Active Noise Cancellation is actually turned on.

  1. With AirPods in your ears, open Control Center on your iPhone (swipe down from the top-right corner on Face ID models, or swipe up from the bottom on Home button models).
  2. Press and hold the volume slider. This expands to show the audio controls.
  3. Tap Noise Control at the bottom of the expanded volume slider.
  4. Select Noise Cancellation. The icon should highlight, indicating ANC is active.

You can also check in Settings > Bluetooth > tap the (i) next to your AirPods > Noise Control. Make sure "Noise Cancellation" is selected, not "Transparency" or "Off."

If ANC is already selected but does not seem to be working, continue with the steps below.

Close-up of a person inserting a wireless earbud into their ear

Photo by Nothing Ahead on Pexels

Run the Ear Tip Fit Test

Apple built an Ear Tip Fit Test into iOS specifically to verify that your AirPods Pro ear tips create a proper seal. A poor seal is one of the most common causes of weak ANC.

  1. Put both AirPods Pro in your ears with the current ear tips attached.
  2. Go to Settings > Bluetooth > tap the (i) next to your AirPods Pro.
  3. Tap Ear Tip Fit Test.
  4. Tap Continue, then tap the Play button. The test plays a short audio clip and uses the internal microphones to measure how much sound leaks out around the ear tips.
  5. The result shows "Good Seal" (green checkmark) or "Adjust or Try a Different Ear Tip Size" for each ear independently.

If either ear shows a poor seal, try a different ear tip size. AirPods Pro come with small, medium, and large tips. Many people need different sizes for each ear, so do not assume both ears use the same size. Remove the current tip by pulling it straight off the AirPod (it clicks into place and clicks off), then press a different size onto the connector until it clicks.

If none of the three included sizes achieve a good seal, third-party memory foam ear tips (such as Comply or Dekoni) compress when inserted and expand to fill the ear canal, providing a tighter seal that improves both passive isolation and ANC performance.

Clean the External Microphones

Each AirPod Pro has multiple microphones: outward-facing ones that capture ambient noise for ANC and inward-facing ones that monitor the sound inside your ear canal. If the outward-facing microphones are dirty, ANC performance degrades because the system cannot accurately sample the noise it needs to cancel.

  1. Remove the ear tips from each AirPod by pulling them straight off.
  2. Look at the exterior of each AirPod. The microphone openings are small mesh-covered holes on the outer surface and near the stem. On AirPods Pro, there is one on the outer face and one on the inner face near where the ear tip attaches.
  3. Use a dry, soft-bristled brush (a clean toothbrush or the brush from an AirPods cleaning kit) to gently sweep across each microphone mesh. Brush away from the opening to avoid pushing debris inside.
  4. For stubborn residue, lightly dampen a cotton swab with 70% isopropyl alcohol and gently wipe each microphone mesh. Let it dry completely (at least two minutes) before reinserting the ear tips.
  5. Clean the ear tips themselves under warm water with mild soap. Rinse thoroughly and dry completely before reattaching them to the AirPods. Do not submerge the AirPods themselves in water.

After cleaning, put the AirPods in your ears, enable ANC, and test near a fan or running faucet. ANC should noticeably reduce the ambient noise level.

Update AirPods Firmware

AirPods firmware updates can fix ANC performance issues caused by software bugs. Apple does not release firmware update notes publicly, but user communities have documented cases where specific firmware versions weakened ANC and subsequent updates restored it.

  1. Go to Settings > Bluetooth > tap the (i) next to your AirPods.
  2. Scroll down to find the Firmware Version number.
  3. AirPods firmware updates are installed automatically. To encourage an update, place the AirPods in their case, connect the case to power (Lightning, USB-C, or wireless), open the lid, and keep your connected iPhone nearby. Leave this setup for at least 30 minutes.
  4. After waiting, check the firmware version again. If it has changed, test ANC performance to see if the update improved it.

Also update iOS on your iPhone through Settings > General > Software Update, as iOS updates can include changes that affect ANC behavior.

Woman sitting at a table with a coffee cup and headphones nearby

Photo by Karolina Kaboompics on Pexels

Reset Your AirPods

If cleaning, fitting new ear tips, and updating firmware did not fix ANC, a full reset clears the AirPods' internal configuration and forces all noise control settings to reinitialize.

  1. Put both AirPods in the charging case and close the lid. Wait 30 seconds.
  2. Open the lid.
  3. On your iPhone, go to Settings > Bluetooth. Tap the (i) next to your AirPods and select Forget This Device.
  4. With the lid open, press and hold the setup button on the back of the case for 15 seconds until the status light flashes amber, then white.
  5. Hold the open case near your iPhone to trigger the pairing animation. Follow the prompts to reconnect.

After re-pairing, immediately test ANC by going to a noisy area and switching between Noise Cancellation and Off. You should hear a clear difference in ambient noise level when ANC is active. If there is no difference, the issue may be hardware-related.

Check for Hardware Damage

If ANC still does not work after all software and cleaning fixes, one or more external microphones may be physically damaged. Hardware damage to ANC microphones can result from:

  • Water damage from wearing AirPods in heavy rain or during intense exercise with excessive sweat
  • Dropping an AirPod onto a hard surface, which can dislodge the microphone component
  • Prolonged exposure to extreme temperatures
  • Debris pushed into the microphone mesh during aggressive cleaning

Contact Apple Support or visit an Apple Store for a diagnostic. If covered by warranty or AppleCare+, Apple replaces the affected AirPod at no charge. Outside of warranty, individual AirPod replacements are available for purchase.

Check Accessibility Settings

iOS Accessibility settings can override AirPods noise control behavior.

  1. Go to Settings > Accessibility > AirPods.
  2. Under Noise Control, verify that Noise Cancellation is included in the modes the stem gesture cycles through. If only "Transparency" and "Off" are selected, squeezing the stem will never activate ANC.
  3. Check the Press and Hold Duration. If set to a very long duration, the gesture may not register. Set it to "Default."

Wireless earbuds resting on a fabric surface with soft natural lighting

Photo by Sound On on Pexels

Related articles you might find helpful:

Frequently Asked Questions About AirPods Noise Cancellation

Which AirPods models support Active Noise Cancellation?

Active Noise Cancellation is available on AirPods Pro (1st and 2nd generation), AirPods Pro 2 (USB-C), AirPods 4 (the ANC model), and AirPods Max. Standard AirPods (1st, 2nd, and 3rd generation) and AirPods 4 (the base model without ANC) do not have noise cancellation hardware and cannot use this feature.

Can I use ANC with only one AirPod in?

On AirPods Pro 2nd generation and later, yes. ANC works with a single AirPod, though performance is reduced because the system has fewer microphones and can only cancel noise on one side. On AirPods Pro 1st generation, ANC is disabled when only one AirPod is in use, and the mode automatically switches to Off or Transparency.

Why does ANC sound different in windy conditions?

Wind blowing across the external microphones creates turbulent noise that the ANC processor struggles to cancel. The anti-noise algorithm is optimized for constant, predictable sounds (like engine hum, air conditioning, or crowd noise) and performs poorly against irregular, chaotic signals like wind gusts. Some AirPods Pro firmware versions include wind noise reduction that detects wind and adjusts the ANC algorithm, but strong wind will always degrade ANC performance.

Does ANC reduce battery life on AirPods?

Yes. ANC requires continuous processing by the onboard chip and constant use of the external microphones, which consumes more power than the Off mode. AirPods Pro typically last about 4.5 to 5 hours with ANC enabled versus 5 to 6 hours with ANC off. Transparency mode uses a similar amount of power as ANC. If battery life is a priority during long listening sessions, switching to Off mode when you do not need noise cancellation extends usage time.

How do I know if my AirPods ANC is working properly?

The best test is switching between ANC and Off mode in a consistently noisy environment (near a fan, air conditioner, or busy street). When you toggle ANC on, you should hear a noticeable reduction in low-frequency background noise, as if someone turned the volume of the outside world down. If switching modes produces no perceptible difference, ANC is not functioning correctly. Run the Ear Tip Fit Test, clean the microphones, and try the fixes outlined above.

사진 지오태깅 및 EXIF 메타데이터 도구

이미지에 위치 메타데이터가 빠져 있나요?

사진에 GPS 위도, 경도, EXIF 태그를 추가해 모든 이미지에 촬영 장소의 기록을 남기세요.

무료로 사용해 보기
Ryan Mitchell
작성

Ryan Mitchell

Ryan Mitchell is a tech journalist and troubleshooting specialist based in Austin, Texas. With over eight years of experience covering consumer electronics, he has written for several technology publications and currently focuses on helping everyday users solve common device problems. Ryan holds a degree in Information Technology from the University of Texas and is an Apple Certified Support Professional. When he is not testing the latest gadgets, he volunteers at a local community center teaching digital literacy to seniors.

관련 글

더 많은 튜토리얼과 로컬 SEO 가이드 보기